FAQ - Questions
We are certified to perform work on all makes and models of air-conditioning, heating, and appliance equipment.
You can give us a call anytime we can usually set up a service call upon 24hrs notice.
We do offer emergency service.
SEER (Seasonal Energy Efficiency Ratio) is a system for rating the efficiency of cooling equipment. The higher the SEER rating, the less your unit will cost to operate.
HSPF (Heating Seasonal Performance Factor) is a measurement similar to SEER, but it measures the efficiency of the heating portion of a heat pump.
AFUE (Annual Fuel Utilization Efficiency) Gas furnaces are rated in this measurement. The higher the AFUE rating, the more efficient the unit.
There are several things that can cause your HVAC system to freeze up. Most need to be corrected by a trained service technician.
Dirty Filter: Making sure the filter is clean or replaced and making sure the airflow is not restricted are about the only things you should check or handle yourself. Should you find that your system was freezing due to a dirty filter, you can speed up the thawing process by replacing the filter and turning the system off and turning on the fan. If you have a heat pump system, you can try turning the system to heating mode until the ice has melted. After the ice has melted, switch the system settings back to normal. If the system refreezes, give us a call to correct the problem.
Low refrigerant: In some cases, freezing up is caused by a leak in the refrigerant lines. The age of the system and the nature and location of the leak are the determining factors on whether to have the system repaired or replaced.
Dirty evaporator coil: Over time, the evaporator coil will become dirty. You will need to have professional help in cleaning the evaporator.
Defective blower motor: A blower motor not running at the proper speed or not running at all will cause freezing.
- There are several things that can cause your system not to heat. Most need to be corrected by a trained service technician.
Always make sure that you have switched your thermostat from cool to heat.
If you have a gas furnace, is your gas turned on?
DO you have electric power on?
- There are many different reason that a particular appliance may not work properly. Most circumstances require a trained technician for a diagnostic check.
- You can check in the service manual that came with the equipment for tips on that equipment.
- Make sure you have power.
- Many problems can be attributed to simply forgetting the sequence of operation, however if you are sure that you have selected the proper choice and the equipment is not doing what it is suppose to then it is time to have it checked out.
- With our program you will have peace of mind knowing your equipment is up to date on routine maintenance, if a problem should ever arise you will receive our priority service response. Click here for our Absolute Maintenance Program.
- All equipment needs proper maintenance to keep it running at peak performance, and to ensure maximum life expectancy.
- You will also notice an energy savings.
Glossary
► Glossary of Industry Terms
AFUE
Annual Fuel Utilization Efficiency. Indicated as a percentage, AFUE tells you how much energy is being converted to heat. For example, an AFUE of 90 means that 90% of the fuel is being used to warm your home while the other 10% escapes as exhaust.
Air Handler
The fan blower, filter and housing parts of a system.
Atmospheric Pressure
The weight of a 1 square inch column of the earth’s atmosphere. At sea level this pressure is 14.696 lb/sq inch
BTU
British Thermal Unit. One BTU is equal to the heat given off by a wooden kitchen match. For heating systems, BTU is a measure of the heat given off when fuel is combusted.
BTUH
BTUs per hour.
Capacity
The ability of your air conditioning or heating system to heat or cool a space. For heating, this is usually expressed in BTUs for cooling and in tons for heating.
CFM
Cubic Feet per Minute. A measurement that indicates how many cubic feet of air pass by a given point in one minute.
Compressor
The compressor controls the pressure applied to the refrigerant. It is necessary for taking in heat to warm your home or getting rid of heat to keep your home cool. It is part of a split-system heat pump or air conditioner’s outdoor unit
Condensation
The process by which a gas is changed into a liquid at constant temperature by heat removal.
Condenser Coil
By converting refrigerant that is in a gas form back to a liquid, the coil sends heat carried by the refrigerant to the outside. The coil is part of the outdoor portion of a split-system air conditioner or heat pump.
Damper
A valve used in ductwork that tightens or loosens so as to control airflow. Typically a damper is used to control the amount of air entering certain areas of your home.
Direct Vent
A heating system that pulls outside air for combustion and vents combustion gases directly outside.
Downflow
This type of furnace takes cool air from the top and blows warm air to the bottom. This type of furnace is common when the furnace is located in a second-floor closet or utility area.
ECM
Electronically Commutated Motor. An ECM is an ultra high efficiency programmable brushless DC motor that utilizes a permanent magnet rotor and a built-in inverter. They are significantly more energy efficient than traditional AC motors and are also much easier to control.
Electronic Air Cleaner
This device filters out large particles and contaminants from indoor air then electronically pulls out tiny particles that have been magnetized, such as bacteria and viruses, then draws them to a collector plate.
Energy Load Analysis
Also known as a Heat Loss Analysis, an energy load analysis is a series of studies performed to estimate the heating or cooling requirements of your home. It takes information such as the square footage of your home, window and door areas, insulation quality and local climate to determine the heating and cooling capacity needed by your furnace, heat pump or air conditioner.
Evaporator Coil
The evaporator coil cools and dehumidifies the air by converting liquid refrigerant into a gas, which absorbs the heat from the air. The warmed refrigerant is then carried through a tube to the outdoor unit. The evaporator coil is part of the indoor portion a split-system heat pump or air conditioner located indoors.
Freon
A general term used to identify, any of a group of partially or completely halogenated simple hydrocarbons containing fluorine, chlorine or bromine, which are used as refrigerants.
Heat Exchanger
The part of a furnace that transfers heat to nearby air.
Heat Loss Analysis
See Energy Load Analysis.
High-Efficiency Furnace
A high-efficiency furnace provides your home with ideal heating comfort while using less energy than other models. High-efficiency furnaces are designed to extract additional heat from natural gas, condensing the flue gases in the process. Also known as a condensing furnace.
Horizontal Flow
A type of furnace that draws in air from one side then heats it. It then sends the warm air out the other side. (Most often used in attics or crawl spaces)
Humidifier
A piece of equipment that adds water vapor to heated air as it moves out of the furnace.
HVAC
Heating Ventilation and Air Conditioning.
HVAC-R
Heating Ventilation Air Conditioning and Refrigeration.
Matched System
A heating and cooling system comprised of products that have been certified to perform at promised comfort and efficiency levels when specifically used together.
Mid-Efficiency Furnace
Equipped with a powered exhaust, Mid-efficiency gas furnaces use a naturally aspirating burner and do not have a continuously lit pilot light. They do not have a draft hood and the seasonal efficiency is much higher than conventional furnaces.
Multi-Poise
A multi-poise furnace can operate in both vertical and horizontal flow orientations.
Payback Analysis
By combining your purchase price and ongoing operating costs, a payback analysis determines the number of years required before monthly energy savings offset the purchase price. A payback analysis will give you an overall measure of the efficiency and value of your heating and air conditioning system.
Puron
Puron R410A refrigerant is an environmentally-sound refrigerant designed not to harm the ozone layer and has been approved as a replacement for older Freon R22 refrigerant. All manufacturers will be required to phase out the production of units using R22 refrigerant by 2010, and the complete phase out of R22 refrigerant will occur by 2030.
Reclaiming
Returning used refrigerant to the manufacturer for disposal or recycling.
Reciprocating Compressor
A type of compressor used in air conditioners that compresses refrigerant by using a piston-like action.
Refrigerant
Refrigerant is a substance that absorbs heat by changing from a liquid to a gas. It then releases this heat in a condenser as the substance returns from a gas back to a liquid.
SEER
Seasonal Energy Efficiency Ratio. This is a measure of the cooling efficiency of your central air conditioner or heat pump. The higher the SEER number, the more efficient the system is at converting electricity into cooling power.
Scroll Compressor
A compressor specially designed to work in a circular motion to compress refrigerant.
Setback Thermostat
A state-of-the-art electronic thermostat with built-in memory that can be programmed for different temperature settings at different times of the day.
Split System
A heat pump or air conditioner that has components in two locations, usually with part of the system located inside and the other outside your home.
Thermostat
A unit that monitors and controls your HVAC system.
Ton
One ton is equal 12,000 BTUH (A unit of measure for cooling capacity)
Upflow
An upflow furnace takes cool air from the bottom and blows warmed air out the top into the ductwork. This type of furnace is usually installed in a basement or an out of the way space.
Ventilator
A ventilators job is to captures heating or cooling energy from stale indoor air and transfers it to fresh incoming air.
Zoning
A way to increase your home comfort and energy efficiency by controlling when and where heating and cooling occurs in a home. Programmable thermostats are used to control operating times of the equipment while dampers are used to direct air flow to certain parts of the home.